63 lines
3.8 KiB
Python
63 lines
3.8 KiB
Python
"""Independent transverse contour measurements from BRep, no operation trace."""
|
||
import math
|
||
from .root_sections import root_band_measurements
|
||
import numpy as np
|
||
from build123d import Plane,Vector,section
|
||
|
||
|
||
def measure_radial_sections(shape, origin, axis, offsets):
|
||
origin = list(origin) if isinstance(origin, Vector) else origin
|
||
axis = list(axis) if isinstance(axis, Vector) else axis
|
||
if any(not isinstance(v,(list,tuple)) or len(v)!=3 or any(type(x) not in (float,int) or not math.isfinite(x) for x in v) for v in (origin,axis)):
|
||
raise ValueError('SECTION_FRAME: origin和axis必须为有限三维向量')
|
||
if Vector(axis).length<1e-9:raise ValueError('SECTION_FRAME: axis不能为零')
|
||
if not isinstance(offsets,list) or any(type(x) not in (float,int) or not math.isfinite(x) for x in offsets):raise ValueError('SECTION_OFFSETS: offsets为有限数值列表')
|
||
if len(offsets)<1 or len(offsets)>12:raise ValueError('SECTION_COUNT: 需要1–12个截面')
|
||
axis=Vector(axis).normalized();origin=Vector(origin)
|
||
ref=Vector(1,0,0) if abs(axis.X)<.9 else Vector(0,1,0)
|
||
u=(ref-axis*ref.dot(axis)).normalized();v=axis.cross(u)
|
||
rows=[]
|
||
for offset in offsets:
|
||
center=origin+axis*offset
|
||
cut=section(shape,section_by=Plane(origin=center,x_dir=u,z_dir=axis))
|
||
faces=list(cut.faces())
|
||
if len(faces)!=1:
|
||
rows.append({'offset_mm':offset,'unavailable':'截面未形成唯一连通区域','regions':len(faces)});continue
|
||
wire=faces[0].outer_wire();data=[]
|
||
for edge in wire.edges():
|
||
for t in np.linspace(0,1,65):
|
||
p=edge.position_at(float(t))-center
|
||
x,y=p.dot(u),p.dot(v)
|
||
data.append((math.atan2(y,x)%(2*math.pi),math.hypot(x,y)))
|
||
data.sort();a=[];r=[]
|
||
for angle,radius in data:
|
||
if a and abs(angle-a[-1])<1e-8:r[-1]=max(r[-1],radius)
|
||
else:a.append(angle);r.append(radius)
|
||
target=np.linspace(0,2*math.pi,4096,endpoint=False)
|
||
radii=np.interp(target,[a[-1]-2*math.pi,*a,a[0]+2*math.pi],[r[-1],*r,r[0]])
|
||
lo,hi=float(min(radii)),float(max(radii));peaks=[]
|
||
if hi-lo>max(.005,hi*.002):
|
||
mask=radii>lo+.8*(hi-lo)
|
||
starts=np.where(mask & ~np.roll(mask,1))[0]
|
||
for start in starts:
|
||
indices=[];i=int(start)
|
||
while mask[i] and len(indices)<len(mask):
|
||
indices.append(i);i=(i+1)%len(mask)
|
||
weights=radii[indices]-lo
|
||
z=np.sum(weights*np.exp(1j*target[indices]))
|
||
peaks.append(float(np.angle(z)%(2*math.pi)))
|
||
peaks.sort();gaps=[(peaks[(i+1)%len(peaks)]-a)%(2*math.pi) for i,a in enumerate(peaks)] if peaks else []
|
||
periodic=len(peaks)>=4 and max(abs(g-2*math.pi/len(peaks)) for g in gaps)<.025
|
||
phase=float(np.angle(np.mean(np.exp(1j*len(peaks)*np.array(peaks))))/len(peaks)*180/math.pi) if periodic else None
|
||
try:
|
||
root_data=root_band_measurements(wire,center,u,v,lo,hi)
|
||
except Exception as exc:
|
||
root_data={'unavailable': '截面曲率/切向求值失败: '+str(exc)[:240]}
|
||
rows.append({'root_band':root_data,'offset_mm':offset,'outer_radius_range_mm':[lo,hi],'outer_lobe_count':len(peaks),
|
||
'equally_spaced':bool(periodic),'phase_modulo_pitch_deg':phase,
|
||
'peak_angles_deg':[math.degrees(a) for a in peaks],
|
||
'max_spacing_error_deg':math.degrees(max(abs(g-2*math.pi/len(peaks)) for g in gaps)) if gaps else None})
|
||
return {'axis':list(axis),'origin':list(origin),'angle_zero_direction':list(u),'sections':rows,
|
||
'note':'由实际实体与截面求交后采样外轮廓;齿状峰数量不是渐开线或压力角证明。相位按一个齿距取模,跨截面比较需避免超过半齿距的混叠。截面必须避开轮毂/支架遮挡,不能用生成参数充当实测。'}
|
||
|