重构 改为标准化输出

backend/live-evals/20260831T103255Z/artifacts/cad_08ca16aaab7f/documents/requirements-draft-v1.json

@@ -0,0 +1,59 @@
+{
+  "items": [
+    {
+      "acceptance_claims": [
+        {
+          "claim_kind": "single_connected_body",
+          "expected": {}
+        },
+        {
+          "claim_kind": "solid_count_equals",
+          "expected": {
+            "value": 1
+          }
+        }
+      ],
+      "assumptions": [
+        "Assume a rectangular base sized 120 mm by 80 mm by 10 mm thick.",
+        "Assume a vertical reinforcing rib centered on the base, 60 mm tall, 8 mm thick, and 70 mm long along the base."
+      ],
+      "draft_id": "draft_001",
+      "source_ids": [
+        "src_001"
+      ],
+      "statement": "Create one connected mounting plate in millimetres with a rectangular base and an attached vertical reinforcing rib, using reasonable assumed dimensions for the plate and rib where the source does not specify exact sizes."
+    },
+    {
+      "acceptance_claims": [
+        {
+          "claim_kind": "through_cylindrical_bore",
+          "expected": {
+            "count": 4,
+            "diameter_mm": 10,
+            "tolerance_mm": 0.1
+          }
+        },
+        {
+          "claim_kind": "circular_hole_pattern",
+          "expected": {
+            "count": 4,
+            "diameter_mm": 10,
+            "pitch_radius_mm": 35,
+            "tolerance_mm": 0.1
+          }
+        }
+      ],
+      "assumptions": [
+        "Assume each mounting hole is 10 mm in diameter.",
+        "Assume the four hole centers lie on a circular pattern with a 35 mm pitch radius, evenly spaced at 90-degree intervals."
+      ],
+      "draft_id": "draft_002",
+      "source_ids": [
+        "src_001"
+      ],
+      "statement": "Add four equally spaced mounting through holes to the plate, using a reasonable assumed hole size and bolt-circle spacing, and verify that the holes form a four-hole pattern."
+    }
+  ],
+  "revision": 1,
+  "schema_version": "cad.requirements-draft.v1"
+}

backend/live-evals/20260831T103255Z/artifacts/cad_08ca16aaab7f/documents/requirements-review-v1.json

@@ -0,0 +1,30 @@
+{
+  "coverage": [
+    {
+      "requirement_ids": [
+        "req_001",
+        "req_002"
+      ],
+      "source_id": "src_001"
+    }
+  ],
+  "issues": [
+    "Draft item 2 assumes a 35 mm pitch radius on an 80 mm-wide base, placing 10 mm holes tangent to the plate edges if centered; this leaves no edge margin and is a weak/unreasonable mounting-hole dimension assumption.",
+    "Draft item 2's circular pattern can conflict with the centered rib geometry from draft item 1, with two hole centers on the rib centerline and likely intersecting the rib footprint; the draft should specify a non-conflicting four-hole layout or adjusted dimensions."
+  ],
+  "item_verdicts": [
+    {
+      "draft_id": "draft_001",
+      "question": null,
+      "reason_code": "none",
+      "verdict": "pass"
+    },
+    {
+      "draft_id": "draft_002",
+      "question": null,
+      "reason_code": "conflict",
+      "verdict": "revise"
+    }
+  ],
+  "verdict": "revise"
+}

backend/live-evals/20260831T103255Z/artifacts/cad_08ca16aaab7f/documents/source-index.json

@@ -0,0 +1,6 @@
+{
+  "schema_version": "cad.source-index.v1",
+  "sources": {
+    "src_001": "Create one connected mounting plate in millimetres with a rectangular base, a vertical reinforcing rib, and four equally spaced mounting through holes. State reasonable dimensions as assumptions, then verify a single connected solid and the four-hole pattern."
+  }
+}