Flange on a plain solid says how to start sheet metal (#2987) (#4789)

* claim: #2987

* Flange on a plain solid says how to start sheet metal (#2987)

Flange, Flat Pattern, and Export DXF on a design with no sheet metal body
now say how to make one: Flange > Base, or Convert to Sheet Metal on a
plate's large flat face. An edge flange checks for a sheet metal body
before it adds a feature. The message is in the catalogs, and engine
messages that match a catalog entry are shown in the interface language.

* Dialogs show a refusal without the engine's parameter prefix (#2987)

The Flange dialog showed "invalid parameters for `sheet.flange`: " in front
of the new guidance. The dialog already names its command, so the red
refusal text leaves that prefix out and follows the interface language
when the message is in the catalogs. Create Issue still gets the full text.
This commit is contained in:
raykholo
2026-10-23 13:44:24 +00:00
committed by GitHub
parent be87303683
commit a0fd39a7be
8 changed files with 69 additions and 6 deletions
+1
View File
@@ -1366,6 +1366,7 @@
"settings.reset_intro": "These settings don't work on this computer and would keep SolidCraft from starting, so they were changed:",
"settings.reset_title": "Settings were changed",
"settings.supersampling_note": "Draws the view at a higher resolution and filters it down: smoother edges, lines and grid on screens below 4K. It costs GPU time: about 2.25× the pixels at 1.5× and 4× at 2×.",
"sheet.no_body": "there is no sheet metal body: start one with Flange > Base, or turn a plate into sheet metal with Convert to Sheet Metal (pick its large flat face)",
"shortcut.json_error": "parameters must be JSON: {error}",
"shortcut.no_command": "no command `{id}`; the text before the JSON must be a command id",
"shortcut.pin": "Pin to the top of the S box",
+1
View File
@@ -1366,6 +1366,7 @@
"settings.reset_intro": "次の設定はこのコンピューターでは使用できず、SolidCraft が起動できなくなるため変更されました:",
"settings.reset_title": "設定が変更されました",
"settings.supersampling_note": "ビューを高い解像度で描画してから縮小します。4K 未満の画面でエッジ、線、グリッドが滑らかになります。GPU の負荷が増えます(1.5× で約 2.25 倍、2× で 4 倍のピクセル)。",
"sheet.no_body": "板金ボディがありません。フランジ > Base で作成するか、板金に変換でプレートを板金に変換してください(広い平面を選択)。",
"shortcut.json_error": "パラメータはJSON形式で指定してください: {error}",
"shortcut.no_command": "コマンド`{id}`がありません。JSONの前のテキストはコマンドIDである必要があります",
"shortcut.pin": "Sボックスの先頭にピン留め",
+1
View File
@@ -1366,6 +1366,7 @@
"settings.reset_intro": "这些设置在此计算机上无法正常工作,会导致 SolidCraft 无法启动,因此已更改:",
"settings.reset_title": "设置已更改",
"settings.supersampling_note": "以更高分辨率绘制视图再缩小:在低于 4K 的屏幕上边、线和网格更平滑。会消耗 GPU 时间:1.5× 时约 2.25 倍像素,2× 时 4 倍。",
"sheet.no_body": "没有钣金实体:请使用法兰 > Base 创建,或使用转换为钣金将板材转换为钣金(选择其较大的平面)。",
"shortcut.json_error": "参数必须采用 JSON 格式:{error}",
"shortcut.no_command": "没有命令 `{id}`;JSON 前的文本必须是命令 ID",
"shortcut.pin": "固定到 S 框顶部",