* claim: #8151
* Opening: a design saved by 0.24 keeps the body a Join To Object runs to (#8151)
Since 0.24.1 a Join extrude To Object also joins the body it runs to
(#6424). Designs saved by 0.24.0 and earlier were built without that,
so on 0.25 the reported box swallowed its lid: the lid's sketch, the
holes, the cut and the moves after it failed.
An extent may now save `to_body_apart: true`, which leaves that body
apart. One pending format change sets it on every Join extrude To
Object of a design of format 39 or older as it opens; designs of
format 40 and later keep the join. Editing the extrude keeps the field.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Markus Kaltenbrunner <kaltenbrunnermarkus@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10852
* Circular pattern: the axis origin takes length expressions and follows them (#10852)
solid.pattern.circular with axis {origin, dir} kept its origin as plain
numbers, so a pattern about a parameter-driven point stayed where the
point was when the pattern was made: the seed moved with the parameter
and the copies did not. Expressions were refused (#248).
The pattern's origin is now a point of expressions, as a Mirror plane's
origin is: numbers or length expressions, evaluated on each rebuild, and
renamed with their parameters. Plain numbers are saved as numbers, as
before. timeline.edit sets pattern.origin as expressions, and editing the
pattern in its dialog keeps them. One pending format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude <noreply@anthropic.com>
`sheet.perforate` takes an optional `sketch` (and `profiles`): the field's
outline. Holes go only inside its closed profiles, out of their inner loops,
`margin` clear of its edges, on a grid from the outline's lower-left corner.
On a folded sheet the outline maps through each panel the sketch lies on and
is clipped to it, so it never reaches a flange in the flat; a sketch on no
face of the sheet is refused. A mirrored copy mirrors the outline, and an
edit that names no sketch (the Perforate dialog has no outline) keeps it.
Without a sketch the field covers the whole sheet as before.
The feature saves `sketch` and `profiles`, a sheet's perforation its outline
in flat coordinates: one pending format note, no migration.
Assisted-by: LLM
* claim: #8822
* Tangent Plane: line it up with a reference plane, at an angle (#8822)
`construct.plane.tangent` takes an optional `reference` (a plane or planar
face) and `angle`. On a cylinder, cone or torus the plane touches where the
face turns towards the reference, turned by the angle about the face's axis,
on the side of the pick; on a sphere it is parallel to the reference. The
plane follows the reference when it moves. The Tangent Plane dialog gets a
Reference plane input and, once one is picked, an Angle field; editing the
plane brings both back. Saved as a pending format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10393
* Per-component History hiding: flag, commands, Browser menu, bar toggle (#10393)
* Carry the new History-hiding strings in the complete catalogs (#10393)
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
Fold the pending design format changes (align-axis-mask, equation-variable-unit, link-file-digests) into format 46.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* feat(engine,ui): allow restricting point-to-point align to chosen axes (#9946)
* style: apply cargo fmt across crates
* fix(clippy): use filter then map instead of bool::then in filter_map
* claim: #9333
* Equation curves: the variable can carry its range's unit (#9333)
A curve can set variable_unit "range" (or tick the new box in its window): the
variable is then a length, so a ^ 2 / (4 * t) is a length when a is one. Start
and end must both be lengths, or one a length and the other a plain number in
the design's unit; anything else is refused. Saved only when set, as one pending
format change; without it curves behave as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Claim #9739
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Linked designs: one changed while the assembly was closed is read when it opens (#9739)
A link now keeps the SHA-256 of its design file's bytes as the assembly
last read them (DesignLink::file_sha256, a pending format change), set by
Insert Design, Relink, Extract to File and Update Links. component.links
reports `changed` from it, hashing a file again only when its time or
size changed (vfs::design_path_stamp, behind the design-path rule). The
app treats a link it meets for the first time whose file changed as not
read yet, so opening an assembly, in its own tab or in place of the blank
design, reads those parts again as a tab coming back does.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Linked designs: read what changed last when a design opens in place of the blank one (#9739)
A read is taken up only by the design revision it started from, and
adopt bumped the revision after starting it, so the read was dropped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude <noreply@anthropic.com>
Fold the pending design format changes (browser-nested-groups, point-cloud-properties, print-faces) into format 45.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Browser: nest groups and reorder components
Groups can hold other groups (up to 8 levels) and be reordered with the
items around them. Sub-components can be reordered too, through a new
`components` list in `browser_order` that is not drawn as a folder.
Document: `BrowserGroup` gains `parent`; group items and `browser_order`
lists hold `BrowserEntry` values (a number is a group, a string an item).
One pending format file; older designs read unchanged. Loading and
refreshing drop what the lists name that is gone, and cut cycles and
over-deep nesting to the top level.
Engine: `browser.group` takes `parent`; `browser.move`, `browser.order`
and `browser.ungroup` handle groups. A change to only the browser's
groups and order no longer re-evaluates the model.
UI: nested rows, dragging a group row (top of a row: before it, the rest:
into it), New Group inside a group, and dropping a placement on the top
of a sibling to reorder it.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Fixed formatting
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Fixed unintended side effect in render scene browser test
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Preserve group order in render workspace
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Increased test coverage
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Updated clipboard test from upstream main for group item type
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* Point clouds: colour and filter by any property of a PLY file, on range tracks (#5151)
A PLY file's other vertex properties are kept as named numbers on the
points (whole-numbered for integer types; a comment `property: 0 name,
1 name` names a label's values). A cloud is coloured by any of them, a
ramp or a palette for whole numbers, and filtered by up to eight, each a
range or a set of named values. The GPU colours and filters the points
itself, so editing a range uploads nothing.
In the Edit Point Cloud card each range is a track, as in an audio
editor: a histogram of the property over what the other filters keep,
stacked by colour, under an overview strip. Ranges are drawn, moved,
snapped to colour changes, typed (Start, End, Length, relative values)
and played (Space or Play). The automatic colour range is exactly the
values the property takes over what the filters keep.
pointcloud.insert and pointcloud.edit take color_by: <property>,
color_range and filters; pointcloud.list reports them with the
properties. docs/point-clouds.md describes it all.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Point clouds: note the saved properties, colouring and filters as a pending format change (#8816)
A design now saves a cloud's per-point columns and their value names, colouring by a property and
filters; an older release must refuse it instead of dropping them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #8429
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Print face: Send to Slicer lays a body on its marked face (#8429)
A body can have one flat print face (Document::print_faces, held by the
certified target a sketch on a face holds). body.print_face {body, point?}
marks or clears it. Send to Slicer, Save Mesh with a slicer and EasyPrint
turn and move the exported copy so the face lies on the bed at Z = 0 with
the centre of mass over the origin; a face that can't be found is a
warning and that body is exported as it lies. Move/Copy and Mirror give a
copy its source's print face. One pending format file; the command
has its own icon (print_face).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Print face: Ctrl+B, the face menu and the Send to Slicer row (#8429)
Ctrl+B and the face context menu mark the selected flat face as its
body's print face, or clear it. Send to Slicer shows the print face of
the one body being sent in a Print face input, takes a flat face picked
in the viewport and clears it when emptied.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Print face: a light tint in the viewport and its strength in Preferences (#8429)
Each visible body's print face is tinted towards the theme's section
colour and outlined, at the strength set under Preferences > General >
Slicer (print_face_highlight, 0 to 1, 20 % by default; 0 hides it). The
user guide describes the print face, and the known limitation after a
shell of a shelled body is listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Fold the pending design format changes (sketch-equation-curves, timeline-joint-folders) into format 44.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #8352
* Sketch: equation-driven curve, a fit point spline from x(t) and y(t) formulas (#8352)
sketch.equation_curve draws a curve from formulas in the expression
language and the design's parameters: x(t) and y(t) over a range of t, or
y = f(x) over a range of x. The curve is a cubic fit spline through fixed
points sampled from the formulas, as many as keep it within a tolerance
(0.01 mm by default, at most 500 points); a curve that ends where it starts
closes smoothly. The sketch keeps the formulas (one new design-format
file), places the points again before every solve so they follow the
parameters, and sketch.equation_curve.edit changes them, keeping the joined
end points. Both commands have input and output schemas.
* Sketch: Equation Curve window, its Edit menu item, labels and guide (#8352)
The ribbon's Equation Curve opens a window for the form (parametric or
explicit), the formulas, the range and the tolerance; OK runs
sketch.equation_curve. Right-clicking an equation curve offers Edit
Equation Curve, which reopens the window on its formulas and runs
sketch.equation_curve.edit. New labels and help in a pending locale file
(with ar, de, he, ja, ko, vi and zh), the icon, the glossary term and the
sketching guide.
* Equation curve: one if for closing the sampled points (clippy collapsible_if)
* claim: #8306
* Timeline: joints in feature folders (#8306)
timeline.group and timeline.move_to_group take joints as well as features, so
hundreds of joints fold into one folder tile. A closed folder shows one tile
whatever it holds; opening it shows its features and joints in both the bottom
and left History. Suppress, delete and ungroup on a folder reach its joints too
(one undo step), deleting a joint removes it from its folder, and an unknown
joint id or name is an error. Saved with the design; designs without joint
folders read and write as before.
* Point clouds: insert PLY, XYZ and PTS scans as a modelling reference (#5151)
A point cloud is kept in the design as a reference, drawn as depth-tested
dots and never a body.
- io: a PLY reader (ASCII, binary little/big endian; x, y, z of any numeric
type, optional colours, other elements skipped; counts checked against the
file) and XYZ/PTS text, thinned evenly past max_points. PLY meshes with
faces can also come in through file.insert_mesh.
- doc: Document.point_clouds (shared f32 points relative to an f64 origin,
colours, units, rigid placement, size and colour), stored as a binary
container part; format change in pending/point-clouds.rs.
- engine: pointcloud.insert / edit / delete / list; doc.open opens a cloud as
a new design; selection.delete takes point_clouds; view bounds include them.
- gpu: an instanced point-sprite pipeline (16 bytes a point).
- ui: Browser Point Clouds folder with eyes, menu and an Edit Point Cloud
card; drop, Open, Insert and file dialogs take .ply/.xyz/.pts; a CPU
viewport fallback; messages in en, en-GB, ja, zh, de and ko.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Point clouds: colour by the file, one colour or height, from the UI (#5151)
The Edit Point Cloud card gets Color By (File Colors, Single Color,
Height). Height is a blue-to-red ramp over design Z, between the cloud's
own two heights or, by default, a range worked out from the points (all
but the lowest and highest 2 %, from an even sample). pointcloud.insert
and pointcloud.edit take color_by and height_range; pointcloud.list
reports them. The colour of each point is worked out in one place
(PointCloud::shade) for the GPU and CPU viewports.
Also: the card's dropdowns compare the picked index (a dropdown's
response doesn't report the pick, so File Units did not change either).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Point clouds: integrate format registration and viewport caches (#5151)
* Point clouds: satisfy current UI audits and document comparisons (#5151)
Route model RGB data through the theme conversion boundary, provide a compact ribbon label, and include point clouds in the new document comparison. Gate the Unix-only CLI-link helper and test so Windows all-target checks remain buildable after the rebase.
* Point clouds: isolate translations for current main (#5151)
Move the existing 74 messages unchanged into one pending locale file and attribute it through a pending row, following the current repository workflow. Repository checks, 50 tooling tests, final workspace Clippy, wasm and generated-catalog equality checks passed after the rebase.
* Point clouds: fit the rebased code to main's GpuTarget and Frame
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Compare point clouds when reusing placement-independent results
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Point clouds: complete command help and required translations (#5151)
* Point clouds: size the save cap from the raised limit after the rebase
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Fix linked component materials and appearances (#7609)
* Linked components: the cached link read carries the source properties
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Update Links: a link without recorded inherited properties is read again
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Preserve authored linked-face overrides and apply cached source properties
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6380
* Cylinder: place by distances from reference edges, like Hole (#6380)
A Cylinder standing on a flat face can take up to two straight edges of
that face as references, each with the distance of its base centre from
the edge's line, measured in the face's plane, as a Single hole does
(#37). `solid.cylinder` takes them as `references: [{edge, distance}]`
with a numeric `base`; the edges are found again by their persistent
names, else their points, so the cylinder follows them when the part
changes, and each distance is a parameter (an input of Inspect Feature).
A cylinder without references stays at its base, as before.
In the Cylinder window, started on a picked face, Reference 1 and 2 take
the edges, each with its Distance measured from the pick, so it works
with the mouse alone; the canvas shows each distance with a box to type
it in, and Edit Feature picks the edges again.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: Edit Feature shows each reference edge input once (#6380)
A face selected when Edit Feature opened the window had already added
the reference inputs; the edit added them a second time.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder references: the measured-once cost test's cylinder has none (#6380)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: pick the face it stands on in its window, then the edges (#6380)
The Cylinder window took its place only from a face selected before it
opened, so started first it stood at the origin and offered no reference
edges. It now has a Face input before Reference 1 and 2, as the Hole
window does: start Cylinder, click the face, click the edges, OK.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Glossary: reference edge, and "Reference" among the words with more than one meaning (#6380)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder edge references: the Cone dialog (#6250) gets the references field too
The Cone primitive landed on main after this branch began; its dialog initialisers lacked
the `refs` field the Primitive kind gained here. The dense form check for Cylinder fills only
its fields: its face and reference edges place it, which the reference tests cover.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: declare references in its contract; reference-placed cylinders are not placement-independent
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #5641
* Cone primitive: solid.cone with base and top radius (#5641)
A cone or truncated cone placed like the cylinder: base centre, axis,
base radius (or diameter), top radius (0, the default, is a full cone)
and height, with the new body / join / cut / intersect choice. It is
built from what the kernel already exposes, a revolve of its half
section about +Z through the origin, moved into place. Toolbar entry
after Torus, a Cone dialog that also places it on a picked face, Edit
Feature, a timeline icon, pending UI strings and attribution, and one
pending design-format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5681
* sketch: exact circular arcs on drawn 3D wires (#5681)
Add WireArc (centre, unit normal, radius, start/end) as an optional analytic
form on drawn 3D sketch wires, with arc_from_3_points, arc_sweep and
sagitta-bounded arc_polyline; add_drawn_arc_in stores the arc, its three
defining fit points and its samples; move_drawn_point re-derives the arc
atomically and refuses collinear points; validate_wires checks saved arcs.
* engine,ui: sketch.arc3d exact 3D arc command (#5681)
sketch.arc3d draws an exact circular arc through three world points in a 3D
sketch, stored analytically beside its fit points and samples; sketch.move3d
rebuilds it, sketch.inspect reports centre/radius/sweep; placement mapping
(map_wire, now shared with the engine's world state) transforms the arc.
One pending design-format file records the new field. The viewport's 3-Point
Arc tool draws a 3D arc when clicked off the sketch plane, with a live arc
preview; the SKETCH panel offers sketch.arc3d.
* ui,engine: 3D Arc button starts an interactive tool (#5681)
sketch.arc3d now maps to a Draw(3) tool handled by sketch3d: three world clicks (start, end, through - same order as the 2D arc tool) run the command, with the live arc preview and snapping. The command is only enabled while a 3D sketch is open, so the toolbar never offers a tool that could only fail. Locale labels for the command.
* ui: cargo fmt
---------
Co-authored-by: RayGalt <RayGalt@pm.me>
* Axes and points from circular edges and round faces
In 3D, a round edge or face stands for its circle wherever a command
takes an axis or a point.
Revolve, Surface Revolve, both Circular Pattern dialogs, Plane at Angle
and Move -> Rotate take a circular edge (through its centre, along its
normal) or a cylinder, cone or torus face (its axis). The features keep
the pick as a model reference, so they follow the model when a parameter
moves it. Straight edges work as before; flat faces are refused.
Every 3D point input takes a circle's centre: construction points (which
follow the circle), To Object, patch points, hole placement, and Move's
pivot and points. Hovering shows the axis as a dashed construction line
or the centre as a star, and the dialog's chip names what the pick
stands for ("centre of edge 10", "axis of face 3").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Format the round-pick hover check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Selection chips: name a round pick as a circle centre or axis
The chip has room for little more than the body and a word or two:
"Shaft · circle centre", "Shaft · circle axis", "Shaft · face 2 axis",
and "Shaft · point" for a point of the model.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move: a circle's centre in a placed component is where the component shows it
Move's pivot and points read a picked circle from the model in its
component's own frame, while the pick is in the world. They now read it
from the world state (and, editing a Move, from the state before it,
placed the same way), as the viewport and the other round picks do.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Plane at Angle on a planar face about a model edge: test that it follows both
Upstream #1956 made a planar face a base for Plane at Angle; this branch makes a model edge an
axis. The rebase keeps both in one PlaneRef::AtAngle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6600
Co-authored-by: Cursor <cursoragent@cursor.com>
* Save an imported mesh that only fits after compression (#6600)
The design file limit was applied to the mesh before Deflate, so a mesh
that had already loaded could not be saved or autosaved.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: validate and version large mesh saves (#6600)
---------
Co-authored-by: Colin Faulkingham <colinfaulkingham@Colins-Mac-mini.local>
Co-authored-by: Cursor <cursoragent@cursor.com>
The component colour tests no longer assume a design always carries a list of
pending format changes; once the release folds them, there is none.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The Joint dialog kept a round edge (a hole's rim), a straight edge and a
corner as plain points where they were picked. When the part got thicker,
a hole moved or the part got longer, the origin stayed where it was and
the jointed part overlapped the other one. An edit that left the picked
spot where it was (lengthening an arm away from the jointed hole) looked
fine, which hid it. Faces and hole walls were already found by name.
The dialog now sends a round edge as its circle's centre with its z, and a
straight edge or corner as an edge pick with its z. The engine keeps them
by name (the round end by its wall and the face across its rim, the edge
and corner by their edge and face names), with the frame the pick showed;
where it can't (no planar face beside the edge, no names), it keeps the
point as before. Edge origins get an optional axis (along the edge, or a
fixed direction) so a hinge on an edge keeps turning about it.
Tests: every joint type and as-built, for each way the dialog picks an
origin, with the arm made thicker, its hole moved and the arm lengthened,
inside one design and through Update Links.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* feat: add colored components inspection toggle
* feat: persist component colors and add cycling controls
* feat: assign component colors in creation order
* fix: update component color menu integration and translations
* fix: proper description for pending format change.
* fix: deleted duplicated format change description from docs/pending.
* Compare the component colour counter in the features-only check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Vadim Kalinsky <vadim@kalinsky.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Test: a text's words follow its text parameters, and so does its cut
A sketch text whose words are an expression of text parameters (`Label + '-L'`): a parameter edit
and a configuration row that sets the parameter relabel the text, the text's cut follows, and the
expression is saved with the design.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Text parameters: a sketch text's words built from them follow every change
A design's parameters are numbers; a text's words (a part label, a size code) could only be typed.
Text parameters hold words: `parameters.add` or `parameters.change` with `unit: "text"` (the
expression is the text, quotes optional), and `sketch.text` and `sketch.edit_text` take
`text_expression` (quoted texts and text parameters joined by `+`, `Label + '-L'`) instead of
`text`. The text is laid out anew from its expression on every evaluation, so a parameter edit,
a configuration row or a script relabels it and the features built on it (a cut, an emboss)
follow in the same rebuild. The design file keeps the text parameters and each text's expression
(one pending format change); a configuration table's parameter column can be a text parameter;
the Parameters dialog lists them under the unit `text`.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Text parameters: the joints' same-but-features check compares the text parameters
The joints are solved once per change unless the design differs only in its features
(same_but_features, #6372), which names every Document field. The text parameters are a
field of their own and change what a text's words evaluate to, so two designs that differ
in them are not the same but for their features.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5938
* Edge flange: height measured from the outer sharp, the inner sharp or the bend tangent (#5938)
An edge flange feature takes height_from (outer, inner or tangent) in sheet.flange and Height From in the Flange dialog, saved only when it is not the outer sharp. A height shorter than the bend takes is refused with the smallest height that fits.
* Edge flange: material outside and tangent bend positions (#5941)
An edge flange's position can now be material_outside (the inner virtual sharp on the edge) or tangent (the bend's outer face tangent to the edge's face), in sheet.flange and the Flange dialog. The bend starting at the edge was already the outside position, which now also answers to bend_outside.
* claim: #4094
* Sheet metal: Path Flange, a chain of bends on an existing sheet edge (#4094)
Path Flange (`sheet.path_flange`): sketch an open chain of lines across a sheet edge, pick the
edge and one line; each line becomes a flange as long as the line and each corner a bend, one
feature and one body. The edge flange takes further bends (`then`), each on the far edge of the
one before, and the Flange dialog shows them as rows with a bin each.
* claim: #4968
* Sheet metal rules: bend angles as the included angle (#4968)
A sheet metal rule's angle_display (bend, the default, or included) sets
how the DXF bend notes read each bend: a 58° bend is B1 UP 122° R1 under
an included rule. The bend table always gives included_angle_deg beside
angle_deg (CSV and JSON). Set in sheet.manage_rules and the Sheet Metal
Rules dialog, listed by sheet.rules; the flange angle stays the bend angle.
* Bend table: the included angle as the CSV's last column, so the columns before it keep their places (#4968)
A test also covers a body whose base flange names its rule, which keeps that rule's notes whichever rule is active, and a bend down.
* Sheet Metal Rules: Angle Display reads Bend or Included, so the choice fits its box (#4968)
The rule editor's row contract lists the new row and the key the dialog sends.
---------
Co-authored-by: begsaquib <saquibbeg4444@gmail.com>
* Sketch Dimension: point or circle to the edge of a circle or arc (#4064)
Adds PointCircleDistance and CircleCircleDistance (edge-based, like #1863):
solver, constructive seed, drawing, command wiring, tests, UI scenarios and docs.
Saved designs gain two constraint kinds, in one pending format file.
Fixes#4064.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Sketch Dimension scenario: pick the circle at its top edge (#4064)
The bottom edge sits under the Dimension tool's status hint in the scenario window, so the second click never reached the tool.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* claim: #4236
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: store an optional sketch and profile selection
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: sweep a sketch profile along the helix
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: accept a sketch and profile selection
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil dialog: pick a sketch profile for the section
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: cargo fmt
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: refuse a loaded sketch coil that also sets the primitive section
A saved design could add section, section_position or start_angle to a
coil that already has a sketch; eval ignored them instead of refusing the
contradiction as the command does.
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil: assert the kernel refusal and exercise hostile profile selections
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Coil dialog: keep the sketch-profile check after rebase
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Format
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Code <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Release 0.22.0: version bump, design format 35
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Release 0.22.0: tests no longer expect the folded render and material changes to be pending
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The Origin folder's eye, a finished sketch's Show Profile and Show Dimensions,
and body locks move from UiState into the design's saved visibility
(origin_hidden, hidden_profiles, shown_dimensions, locked_bodies), so each tab
keeps its own and they survive closing the design. The Sketches folder uses the
saved browser folder (c0/sketches in hidden_folders); ui.set/ui.inspect keep
showOrigin, showSketches, hiddenProfiles, shownDims and lockedBodies.
Preferences > Design > "Hide origin by default": a design that never toggled
its Origin eye follows the preference. New fields are a pending format change
(format/pending/browser-view-state.rs).
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>