3db45df8be
4 commits, squashed; the originals stay reachable from tag archive/merge-main-develop. - c19500fce jyviko: Fillet: the radius-too-large choice in plain nouns - b75d17667 jyviko: kernel: a round that would cut through its wall into a hollow is refused - 795394417 jyviko: Fillet rig: 1668's R7 past the inside corner is refused at 4 + 2 sqrt2 - a26d3ee41 jyviko: xtask: known-failing grades a nextest junit report against tests/KNOWN_FAILING_TESTS Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
24 lines
3.0 KiB
Plaintext
24 lines
3.0 KiB
Plaintext
# The fillet cases that fail today, one a line: `<case> <why it fails today>`. Sorted. The fillet
|
|
# rig gate (.github/workflows/fillet-rig.yml) fails on a case that fails and is not listed here,
|
|
# and on a listed case that passes: a fix removes its line in the same pull request.
|
|
# Baseline: develop 242bbc89f with the SMLib fixes of 2026-10-29 (integration-overnight + b78bd4a), aarch64 Linux.
|
|
1080-fillet-equal-slope-basin-1-mm-rim-loop-4 not supported yet: a convex round past its face is not yet built by subtraction
|
|
1080-fillet-sloped-basin-0-5-mm-rim-r4-4-edges not supported yet: a convex round past its face is not yet built by subtraction
|
|
1080-fillet-sloped-basin-1-mm-rim-r4-2-edges not supported yet: a convex round past its face is not yet built by subtraction
|
|
1080-fillet-sloped-basin-1-mm-rim-r4-4-edges not supported yet: a convex round past its face is not yet built by subtraction
|
|
1207-fillet-bar-top-edge-after-boss-arc-round-r0-5 SMLib's check refuses the round: internal coincident control points in a B-spline curve (an internal pole)
|
|
190-fillet-disc-rim-past-its-2mm-wall SMLib status 1001: a convex round past its face is not yet built by subtraction
|
|
2893-chamfer-distance-and-angle-past-the-wall-refused refused for another reason: SMLib SM_ERR_INVALID_INPUT, not a check saying the angle runs past the wall
|
|
2893-chamfer-two-distances-elliptical-rim SMLib status 1001 on the elliptical rim's chamfer
|
|
2893-chamfer-two-distances-past-the-bottom SMLib status 1001: SmFilletNx1ClosedCorner cannot compute the closed rim's corner geometry, where the chamfer past the bottom rim should build the frustum
|
|
4782-fillet-bar-edge-wider-than-both-faces SMLib status 1001: a convex round past both its faces is not yet built by subtraction
|
|
5158-fillet-round-just-past-a-10mm-face SMLib status 1001: a convex round 0.01 past its face is not yet built by subtraction (10.0001-10.04 open)
|
|
9-fillet-corner-curvature-with-reduce-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
|
|
9-fillet-corner-curvature-with-taper-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
|
|
926-chamfer-top-edge-ending-on-boss-wall-above-it not supported yet: the chamfer is refused as larger than its faces where it ends on the boss's wall
|
|
cov-chamfer-concave-edge-through-up-down-joined-squares SMLib status 1001 on the concave chamfer's tangent chain
|
|
cov-chamfer-outer-corner-edge-of-a-shelled-box-with-a-lip SMLib's chamfer result is not a closed solid where it ends on the lip
|
|
cov-fillet-arc-edge-on-an-oblique-cut-of-a-bar SMLib's check refuses the round: internal coincident control points in a B-spline curve
|
|
every-block-cylinder-crease-top-edge-after-arc-round-r1 the r1 round's contact seam with the block's side face reads 60 degrees (the cylinder wall's normal) at its end on the crease (8.660, 5, 15.284): G0 where the round is built tangent
|
|
every-hole-top-rim-r12-past-plate-bottom SMLib status 1001: a convex round past its face on the tangent side is not yet built by subtraction
|