bcdee6e0bb
* claim: #8284 Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com> * Sketch on a face: a round's edges that end a hair apart still close (#8284) Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com> * Sketch on a face: test both ends of a rounded loft end to end (#8284) A square lofted to a circle with its side edges rounded, as in the report: a sketch on either end face takes the whole face. Without the fix the circular end fails with "face projection has a branched boundary". Also drops a redundant term from the join tolerance. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> --------- Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
45 lines
2.6 KiB
Rust
45 lines
2.6 KiB
Rust
//! A sketch on an end face of a loft whose side edges are rounded (#8284). The rounds' fitted edges
|
|
//! end a few 1e-5 mm short of the face's other edges, and where a round dies away at a corner the
|
|
//! mesh keeps an edge from a point to itself; the face's outline still closes into one profile.
|
|
|
|
use solidcraft_geom::Vec3;
|
|
|
|
use super::*;
|
|
|
|
/// A 40 mm square at z = 0 lofted to a circle of radius 25 at z = 40, its four side edges rounded.
|
|
fn rounded_loft(s: &mut Session) {
|
|
run(s, "sketch.create", json!({"plane": "XY", "name": "Square"}));
|
|
run(s, "sketch.rectangle.two_point", json!({"p0": [-20, -20], "p1": [20, 20]}));
|
|
run(s, "sketch.finish", json!({}));
|
|
run(s, "sketch.create", json!({"plane": "XY", "offset": 40, "name": "Circle"}));
|
|
run(s, "sketch.circle.center", json!({"center": [0, 0], "radius": 25}));
|
|
run(s, "sketch.finish", json!({}));
|
|
let section = |name: &str| json!({"sketch": name, "profiles": [{"point": [0, 0]}]});
|
|
run(s, "solid.loft", json!({"sections": [section("Square"), section("Circle")], "operation": "new", "body_name": "Loft"}));
|
|
// Each side edge runs from a corner of the square to the circle; pick it halfway up.
|
|
let mid = (20.0 + 25.0 * std::f64::consts::FRAC_1_SQRT_2) / 2.0;
|
|
let edges: Vec<Value> = [(1.0, 1.0), (1.0, -1.0), (-1.0, 1.0), (-1.0, -1.0)].iter().map(|(x, y)| json!([x * mid, y * mid, 20])).collect();
|
|
run(s, "solid.fillet", json!({"edges": edges, "radius": 3}));
|
|
}
|
|
|
|
#[test]
|
|
fn a_sketch_on_either_end_of_a_rounded_loft_takes_the_whole_face() {
|
|
let mut s = Session::default();
|
|
rounded_loft(&mut s);
|
|
for up in [-1.0, 1.0] {
|
|
let world = s.world_state();
|
|
let loft = world.body("Loft").unwrap();
|
|
let face = loft.body.faces(0.01).unwrap().into_iter().find(|f| f.plane_normal.is_some_and(|n| n.dot(Vec3::Z * up) > 0.999)).unwrap();
|
|
let pick = json!({"body": "Loft", "index": face.index, "face": [face.centroid.x, face.centroid.y, face.centroid.z]});
|
|
let id = run(&mut s, "sketch.create", json!({"plane": pick}))["sketch"].as_u64().unwrap();
|
|
run(&mut s, "sketch.finish", json!({}));
|
|
let mut s2 = Session::new((*s.doc).clone());
|
|
run(&mut s2, "solid.extrude", json!({"sketch": id, "distance": 5, "operation": "new", "body_name": "Pad"}));
|
|
let state = s2.model.state();
|
|
let pad = state.bodies.iter().find(|b| b.name == "Pad").unwrap();
|
|
let v = pad.body.tessellate(1e-2).unwrap().measure().volume;
|
|
// The projected outline fits the round with splines, so it is close to the face, not exact.
|
|
assert!(rel(v, face.area * 5.0) < 1e-2, "end {up}: {v} vs {}", face.area * 5.0);
|
|
}
|
|
}
|