* claim: #5172 * Extrude without profiles keeps nested loops as holes (#5172) With no `profiles`, solid.extrude took every region of the sketch, so circles drawn inside a plate outline were extruded as well and filled the plate's holes. The default now applies even-odd nesting to the drawn profiles: a loop inside an outline is its hole, a loop inside that hole is material again, and separate outlines all extrude. Sketches without nesting keep the `all` selection, and explicit `profiles` (including "all") are unchanged. Saved designs store their selection, so they recompute as before.
This commit is contained in:
@@ -25,7 +25,7 @@ pub static COMMANDS: &[CommandSpec] = &[
|
||||
.key("E")
|
||||
.contract(&EXTRUDE_CONTRACT)
|
||||
.output(output_schema_for::<FeatureResult>)
|
||||
.params("distance: expr (or through_all: true); taper?: angle expr; sketch?: id|name (default: active or last sketch); profiles?: all | [index] | [{curves: [ids]}] (the profile whose outer loop is made of exactly these curves, or pieces of them; found again on every recompute, so it follows parameter changes; islands inside are its holes; an error when no profile or several match) | [{point:[x,y]}] (index and point picks are stored by their curves when that finds the same profile); face?: [x,y,z] (extrude a planar body face instead of a sketch profile); faces?: [[x,y,z],…] (coplanar faces of one body); face_body?: name (whose face, where faces of several bodies meet at the point); direction?: positive|negative|symmetric (distance is total thickness, split evenly around the start plane); convention?: total_distance|legacy_per_side (default total_distance; legacy preserves older symmetric extents); distance2?: expr (Two Sides: a second distance the other way from the first side, which may be through_all or to; with direction: negative the first side goes against the normal and distance2 along it); start_offset?: expr (along the sketch normal, also with direction: negative); to?: [x,y,z] (To Object: a face, vertex or point; to_offset?: expr past it); from?: [x,y,z] (From Object: start at that face or point); operation?: new|join|cut|intersect|auto (cut into a body, otherwise join existing solids; new in an empty component); targets?: [body] (Join from a face, or from a sketch on a body's face, defaults to that face's body; explicit targets or participants override); name?; body_name?; thin?: true (Thin: a wall along sketch curves instead of the profiles) with curves?: [curve ids] (open chains and closed loops, joined where they meet end to end; default: every drawn curve of the sketch), thickness: expr, side?: center|inside|outside|two_sides (a closed loop's inside is the area it encloses, an open chain's the side it bends toward, a straight line's the left of its first curve as drawn; default center), thickness2?: expr (two_sides: the thickness outside); corners are mitred, crossing walls are one"),
|
||||
.params("distance: expr (or through_all: true); taper?: angle expr; sketch?: id|name (default: active or last sketch); profiles?: all | [index] | [{curves: [ids]}] (the profile whose outer loop is made of exactly these curves, or pieces of them; found again on every recompute, so it follows parameter changes; islands inside are its holes; an error when no profile or several match) | [{point:[x,y]}] (index and point picks are stored by their curves when that finds the same profile); default: every drawn profile, except that a loop inside another is its hole and a loop inside that hole is material again; face?: [x,y,z] (extrude a planar body face instead of a sketch profile); faces?: [[x,y,z],…] (coplanar faces of one body); face_body?: name (whose face, where faces of several bodies meet at the point); direction?: positive|negative|symmetric (distance is total thickness, split evenly around the start plane); convention?: total_distance|legacy_per_side (default total_distance; legacy preserves older symmetric extents); distance2?: expr (Two Sides: a second distance the other way from the first side, which may be through_all or to; with direction: negative the first side goes against the normal and distance2 along it); start_offset?: expr (along the sketch normal, also with direction: negative); to?: [x,y,z] (To Object: a face, vertex or point; to_offset?: expr past it); from?: [x,y,z] (From Object: start at that face or point); operation?: new|join|cut|intersect|auto (cut into a body, otherwise join existing solids; new in an empty component); targets?: [body] (Join from a face, or from a sketch on a body's face, defaults to that face's body; explicit targets or participants override); name?; body_name?; thin?: true (Thin: a wall along sketch curves instead of the profiles) with curves?: [curve ids] (open chains and closed loops, joined where they meet end to end; default: every drawn curve of the sketch), thickness: expr, side?: center|inside|outside|two_sides (a closed loop's inside is the area it encloses, an open chain's the side it bends toward, a straight line's the left of its first curve as drawn; default center), thickness2?: expr (two_sides: the thickness outside); corners are mitred, crossing walls are one"),
|
||||
CommandSpec::new("solid.revolve", "Revolve", revolve)
|
||||
.at("SOLID", "CREATE")
|
||||
.icon("revolve")
|
||||
@@ -653,6 +653,7 @@ fn extrude(s: &mut Session, p: &Value) -> Result<Value> {
|
||||
profiles: match face_profile {
|
||||
Some(f) => f,
|
||||
None if thin.is_some() => ProfileSel::All,
|
||||
None if p.get("profiles").is_none() => default_extrude_profiles(s, sketch),
|
||||
None => profiles(p, cmd)?,
|
||||
},
|
||||
extent,
|
||||
@@ -663,6 +664,47 @@ fn extrude(s: &mut Session, p: &Value) -> Result<Value> {
|
||||
add_feature(s, p, kind)
|
||||
}
|
||||
|
||||
/// The profiles an extrude takes when `profiles` is omitted: even-odd nesting over what was drawn,
|
||||
/// so a loop inside an outline is its hole and a loop inside that hole is material again (#5172).
|
||||
/// Without nesting this is `All`, as before. When the pick cannot be stored so that it finds the
|
||||
/// same profiles again (the sketch is not solved, or two profiles share their curves), it stays
|
||||
/// `All` too.
|
||||
fn default_extrude_profiles(s: &Session, sketch: u64) -> ProfileSel {
|
||||
let st = s.model.state();
|
||||
let Some(ss) = st.sketch(sketch) else { return ProfileSel::All };
|
||||
let drawn = solidcraft_sketch::find_drawn_profiles(&ss.sketch);
|
||||
let ps = if drawn.is_empty() { ss.profiles.clone() } else { drawn };
|
||||
if ps.len() > 10_000 || ps.iter().all(|p| p.region.holes.is_empty()) {
|
||||
return ProfileSel::All;
|
||||
}
|
||||
// Each profile has the profiles directly inside it as holes, so the number of holes around a
|
||||
// point of a profile's material is its nesting depth.
|
||||
let material: Vec<_> = ps
|
||||
.iter()
|
||||
.filter(|p| {
|
||||
let probe = p.region.interior_point();
|
||||
ps.iter().filter(|other| other.region.holes.iter().any(|hole| hole.contains(probe))).count() % 2 == 0
|
||||
})
|
||||
.collect();
|
||||
let all = solidcraft_sketch::without_text_counters(&ss.sketch, ps.clone());
|
||||
if material.iter().map(|p| &p.outer_curves).eq(all.iter().map(|p| &p.outer_curves)) {
|
||||
return ProfileSel::All;
|
||||
}
|
||||
// Profiles of the solved sketch itself are stored by index, which `stable_profiles` turns
|
||||
// into curves; drawn profiles of a sketch with projected references are named by curves.
|
||||
let same = ps.len() == ss.profiles.len() && ps.iter().zip(&ss.profiles).all(|(a, b)| a.outer_curves == b.outer_curves);
|
||||
let sel = if same {
|
||||
let indices = ps.iter().enumerate().filter(|(_, p)| material.iter().any(|m| std::ptr::eq(*m, *p))).map(|(i, _)| i).collect();
|
||||
ProfileSel::Indices { indices }
|
||||
} else {
|
||||
ProfileSel::Curves { loops: material.iter().map(|p| p.outer_curves.clone()).collect() }
|
||||
};
|
||||
match solidcraft_doc::profile_selection_indices(ss, &sel) {
|
||||
Ok(found) if found.len() == material.len() && material.iter().all(|p| !p.outer_curves.is_empty()) => sel,
|
||||
_ => ProfileSel::All,
|
||||
}
|
||||
}
|
||||
|
||||
/// The body whose face `sketch` is attached to (on the face itself, not offset from it), when
|
||||
/// it is one the active component works on ([`active_scope`]).
|
||||
fn sketch_face_body(s: &Session, sketch: u64) -> Option<String> {
|
||||
|
||||
@@ -3381,6 +3381,47 @@ fn deleting_a_sketch_leaves_no_silently_failing_feature() {
|
||||
}
|
||||
}
|
||||
|
||||
#[test]
|
||||
fn default_extrude_profiles_preserve_two_holes() {
|
||||
let mut sketch = Session::default();
|
||||
run(&mut sketch, "sketch.create", json!({"plane": "XY"}));
|
||||
run(&mut sketch, "sketch.rectangle.two_point", json!({"p0": [0, 0], "p1": [60, 40]}));
|
||||
for x in [15, 45] {
|
||||
run(&mut sketch, "sketch.circle.center", json!({"center": [x, 20], "radius": 5}));
|
||||
}
|
||||
run(&mut sketch, "sketch.finish", json!({}));
|
||||
for (selection, expected) in [
|
||||
(None, (2400.0 - 50.0 * PI) * 5.0),
|
||||
(Some(json!([0])), (2400.0 - 50.0 * PI) * 5.0),
|
||||
(Some(json!("all")), 12000.0),
|
||||
(Some(json!([0, 1, 2])), 12000.0),
|
||||
] {
|
||||
let mut s = Session::new((*sketch.doc).clone());
|
||||
let mut params = json!({"distance": 5});
|
||||
if let Some(selection) = selection {
|
||||
params["profiles"] = selection;
|
||||
}
|
||||
run(&mut s, "solid.extrude", params);
|
||||
let actual = volume(&mut s);
|
||||
assert!(rel(actual, expected) < 1e-4, "{actual} vs {expected}");
|
||||
}
|
||||
}
|
||||
|
||||
#[test]
|
||||
fn default_extrude_profiles_keep_even_depth_islands_and_separate_outlines() {
|
||||
let mut s = Session::default();
|
||||
run(&mut s, "sketch.create", json!({"plane": "XY"}));
|
||||
for (p0, p1) in [([0, 0], [30, 30]), ([5, 5], [25, 25]), ([10, 10], [20, 20]), ([40, 0], [50, 10])] {
|
||||
run(&mut s, "sketch.rectangle.two_point", json!({"p0": p0, "p1": p1}));
|
||||
}
|
||||
run(&mut s, "sketch.finish", json!({}));
|
||||
run(&mut s, "solid.extrude", json!({"distance": 5}));
|
||||
assert_eq!(s.model.state().bodies.len(), 3);
|
||||
let expected = (900.0 - 400.0 + 100.0 + 100.0) * 5.0;
|
||||
let actual = volume(&mut s);
|
||||
assert!(rel(actual, expected) < 1e-6, "{actual} vs {expected}");
|
||||
}
|
||||
|
||||
/// Every body a multi-profile `new` extrude creates carries its `body_name`, not a generic BodyN (#266).
|
||||
#[test]
|
||||
fn multi_profile_extrude_names_every_body_after_body_name() {
|
||||
|
||||
Reference in New Issue
Block a user