* claim: #754
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Sketch Dimension: arc length from an arc and its end point (#754)
The arc-length dimension existed (sketch.dimension type arc_length) but
the Dimension tool could only give an arc its radius. An arc and one of
its own end points, in either order, now dimension the arc's length:
click the arc, then its end. The pair was refused before ("cannot
dimension that combination"), so no existing result changes. A point
where the arc's end is (a coincident line end) counts as that end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
CommandSpec::new("sketch.point","Point",draw_point).at("SKETCH","CREATE").icon("point").enabled(in_sketch).params(concat!("point: [x,y] (each a number or an expression over the design's parameters: the point is then fixed where it comes to and follows them) or a snap: \"mid:<line>\" (held at the line's midpoint), \"on:<curve>:x,y\" (on the curve near x,y), {vertex: [x,y,z]} or {on_edge: [x,y,z]} of the model; id?",connect_doc!(),created_doc!())),
"entities: [refs] (a line midpoint is \"mid:line_id\"), type?: auto|distance|horizontal|distance_x|vertical|distance_y|length|radius|diameter|angle, value?: number or expression (default: current; a bare number is in the design's units, e.g. 2 means 2 in in an inch design; give a unit such as \"50 mm\" to override), or `name = expression` (e.g. \"width = 40\"; also `#name = expression`), which adds the user parameter `name` with that expression and dimensions with `name` (refused when the name is taken or reserved; the reply's `defined` names it); text_at?: [x, y]. Two points or a line off the axes: with auto, text_at across from them is the distance between them, above or below them horizontal, beside them vertical. Two midpoints: placing text above or below their bounding box measures horizontally, beside it vertically. Two lines: the angle between them (acute, or 180° − it when the value is nearer that) unless text_at picks a sector. A line and a circle or arc: the distance from the line to its edge (the gap, or how far the edge reaches past a line that cuts it; 0 is tangent); dimension the centre point for the distance to the centre. A point and a circle or arc: the distance from the point to its edge (or how far within it a point inside lies). Two circles or arcs: the gap between their edges (or how far they overlap when they cross, or the narrowest gap between them when one lies inside the other); dimension their centre points for the distance between centres. A dimension the sketch already determines is refused (naming what determines it); if_redundant?: \"driven\" places it as a driven (reference) dimension instead. scale_sketch?: bool (the dimension tool sends true): when this is the sketch's first length dimension and nothing in the sketch fixes a size (no other driving length dimension, nothing fixed or projected), the whole sketch scales about its origin to the value instead of distorting. Returns measured in unit (mm or deg), and scaled: the factor when the sketch was scaled",
"entities: [refs] (a line midpoint is \"mid:line_id\"), type?: auto|distance|horizontal|distance_x|vertical|distance_y|length|radius|diameter|angle, value?: number or expression (default: current; a bare number is in the design's units, e.g. 2 means 2 in in an inch design; give a unit such as \"50 mm\" to override), or `name = expression` (e.g. \"width = 40\"; also `#name = expression`), which adds the user parameter `name` with that expression and dimensions with `name` (refused when the name is taken or reserved; the reply's `defined` names it); text_at?: [x, y]. Two points or a line off the axes: with auto, text_at across from them is the distance between them, above or below them horizontal, beside them vertical. Two midpoints: placing text above or below their bounding box measures horizontally, beside it vertically. Two lines: the angle between them (acute, or 180° − it when the value is nearer that) unless text_at picks a sector. A line and a circle or arc: the distance from the line to its edge (the gap, or how far the edge reaches past a line that cuts it; 0 is tangent); dimension the centre point for the distance to the centre. A point and a circle or arc: the distance from the point to its edge (or how far within it a point inside lies). Two circles or arcs: the gap between their edges (or how far they overlap when they cross, or the narrowest gap between them when one lies inside the other); dimension their centre points for the distance between centres. An arc and one of its end points: the arc's length (type arc_length does it from the arc alone). A dimension the sketch already determines is refused (naming what determines it); if_redundant?: \"driven\" places it as a driven (reference) dimension instead. scale_sketch?: bool (the dimension tool sends true): when this is the sketch's first length dimension and nothing in the sketch fixes a size (no other driving length dimension, nothing fixed or projected), the whole sketch scales about its origin to the value instead of distorting. Returns measured in unit (mm or deg), and scaled: the factor when the sketch was scaled",
radius, diameter and angle dimensions. Each is a parameter
radius, diameter, arc length and angle dimensions. For an arc's length, click the arc and then one of its end points. Each is a parameter
(`d1`, `d2`, …), so it can hold an expression.
Press D, click what you want to measure and type the value: as soon as the click settles the
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.